MILLIPUT : MASTIC : REF : MIL01 : STANDARD YELLOW-GREY (JAUNE-GRIS) (Two Part Epoxy Putty) (113,4g)
Numéro d'article :
MIL01
Fabricant :
MILLIPUT.
Mastic Epoxy.
ISBN : 5035167000490.
---
Chaque carton contient 113,4 g.
Un bâtonnet de 56,7 g de chaque composant. Il existe six qualités différentes de Milliput :
- Bleu turquoise.
- Standard (jaune/gris).
- Terre cuite.
- Gris argenté.
- Noir.
- Blanc extra-fin.
Milliput peut être utilisé pour réparer de nombreux types de matériaux, notamment les métaux, les plastiques, la maçonnerie, le bois, le verre et la céramique, et peut être utilisé là où le soudage est impossible.
Pourquoi choisir Milliput ?
Il est :
Autodurcissant.
Ne rétrécit pas.
Résistant et durable.
Prend en charge sous l'eau.
Isolant électrique.
Résistant à l'eau, à la chaleur et aux produits chimiques.
Forte adhérence sur la plupart des matériaux.
Se moule comme du mastic et prend en charge comme de la roche.
---
Plus d'informations :
Milliput est un excellent adhésif et permet de coller les matériaux suivants entre eux ou avec d'autres : bois, brique, ciment, métaux, béton, plastiques, verre, etc. Notez toutefois que Milliput n'est pas conçu pour être appliqué en couche mince. Milliput durcit sous l'eau et résiste à la chaleur jusqu'à 130 °C.
Mélanger à parts égales chaque bâtonnet du paquet. Pétrir et rouler dans les mains pendant au moins 5 minutes jusqu'à ce que les couleurs se mélangent et deviennent uniformes sans laisser de traces, puis mélanger pendant une minute supplémentaire. Les surfaces sur lesquelles le mastic est appliqué doivent être exemptes de graisse et de saleté. Les surfaces lisses doivent être nettoyées avec un solvant approprié ou à l'eau chaude savonneuse pour éliminer la saleté et la graisse. Un ponçage de la surface améliorera l'adhérence. Le mastic peut alors être appliqué et durcira en trois à quatre heures sans rétrécissement.
À toutes les étapes, du mélange initial à la prise finale, Milliput réagit à l'eau. Pour faciliter la manipulation et éviter le collage, il est conseillé de maintenir les doigts et les outils humides. Dans certains cas, le travail peut être effectué sous un léger jet d'eau sous le robinet. Pour obtenir une finition lisse, moulez ou appliquez Milliput, puis essuyez et lissez immédiatement avec les doigts mouillés ou un chiffon fin et humide.
Les outils utilisés pour appliquer ou modeler Milliput doivent être nettoyés immédiatement après utilisation. Si le mastic durcit, il sera presque impossible à enlever.
À l'état de mastic, Milliput, comme la plupart des produits chimiques d'usage domestique, peut irriter les peaux sensibles. Pour mélanger les deux composants, il est conseillé d'utiliser des gants en caoutchouc ou des gants jetables en polyéthylène. Si vous avez utilisé des gants en caoutchouc, lavez-les immédiatement après utilisation et, tant qu'ils sont encore en place, à l'eau courante. Si vous avez utilisé vos mains pour mélanger ou manipuler Milliput, lavez-les immédiatement après utilisation avec du savon de toilette et de l'eau tiède.
Pour le moulage ou la fabrication de moules, du talc ou une huile légère peuvent être utilisés comme agent de démoulage.
Les produits Milliput résistent au gel, à la chaleur, aux solvants et à la plupart des carburants.
---
Each cartons containing 113.4gm.
One 56.7gm stick of each part. There's six differents grades of Milliput :
-Turquoise blue.
-Standard (Yellow/Grey).
-Terracotta.
-Silver Grey.
-Black.
-Superfine White.
Milliput can be used for repairs on many types of materials including metals, plastics, masonry, wood, glass and ceramics and can be used in places where welding is impractical.
Why Milliput?
It is:
Self hardening.
Non shrinking.
Tough and durable.
Sets underwater.
Electrically insulating.
Water, heat and chemical resistant.
Highly adhesive to most materials.
Moulds like putty - sets like rock.
---
More informations :
Milliput is an excellent adhesive and will bond any of the following to itself or to any of the others - wood, brick, cement, metals, concrete, plastics, glass etc, but note that Milliput is not intended as a thin layer adhesive. Milliput will set under water and is heat resistant up to 130°C.
Mix together equal parts of each stick from the pack. Knead and roll in the hands for at least 5 minutes until the colours merge and become uniform and no streaks can be seen, and then mix for another minute. The surfaces to which the putty is applied should be free from grease and dirt. Smooth surfaces should be cleaned with a suitable solvent or with soap and warm water to remove dirt and grease. Abrading the surface will improve adhesion. the putty may now be applied and will set hard in three to four hours without shrinking.
At all stages from initial mixing to final setting Milliput responds to the use of water. To aid manipulation and avoid sticking, fingers and tools should be kept moistened with water. There are certain instances when work may be carried out in a gentle stream of water under a tap. To obtain a smooth finish, mould or apply Milliput and then immediately wipe and smooth gently with wet finger or with a fine textured moist cloth.
When tools have been used for applying or contouring Milliput they should be cleaned immediately after use. If the putty is allowed to harden on it will be almost impossible to remove.
In the putty state Milliput, like most chemicals in domestic use, may cause irritation to sensitive skins. When mixing the two components it is advisable to use rubber gloves or throw-away polythene gloves. When rubber gloves have been used wash them immediately after use, and whilst still on the hands, using running water. If the hands have been used for mixing or manipulating Milliput wash them immediately after use with toilet soap and warm water.
When casting or mouldmaking talc or a light oil can be used as a releasing agent.
Milliput products are resistant to frost, heat, solvents and most fuels.